Maintained in May 2025. 2 types of weights are included. SAEC long tone arms are highly regarded for their high accuracy. Hard ruby is used for the double knife-edge bearing, and it is characterized by clear, crisp sound quality and accurate sound images. Overall there is dullness (Oikawa Tetsuji)
Maintenance information: 2025.5.2 maintained (DIN terminal replaced with a new one made by USA CARDAS AUDIO, connector, new replacement, inside force canceller weight, genuine product addition, RCA phono cable, external product addition, arm, shell terminal, RCA cable, etc., overall cleaning)
Accessories: instruction manual phono cable (external product), M DIN
Main Specifications: [WE-308L] Double Knife Edge Static Balance Universal Type Total Length 367.5 mm Overhang 5 mm Cartridge Usage Range 12.8 g to 19.8 g (when using standard weights for both shells)
※There is no IN/OUT of TAPE2, and the AUX and TUNER INPUT button locks are sweet, so it's cheap. Maintained! AGI's popular 511 preamp. The speedy and straight sound expression goes well with classical jazz, rock, etc., and also matches well with vintage speakers. The power is turned on when the outlet is inserted, but it is the original specification (the front switch is for a service outlet). In addition to the exterior and described above, you can also see a feeling of use such as dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2026.5.12 maintenance completed (power supply resistor, film C short diode replacement, each SW cleaning) 2022.3.17 maintenance (attached to pin jack TAPE1 input and output. TAPE2 (input/output) hole blocking, operation check) 2022.3.10 maintenance (each SW, Vol cleaning, RCA earth cleaning, hot side pin soldering treatment)
Accessories: none
Main specifications: 1 phono input system (MM compatible), 2 line input systems, frequency characteristics 20 to 20 kHz, W430 x H165 x D285 mm, approx. 8.7 kg
* Operation has been confirmed, but since it is not compatible with the manufacturer, it will be delivered as is at a low cost. Pioneer network player. In addition to the ability to play back high-resolution files stored on the NAS via a network, it can also be used as a USB DAC by connecting to a PC. Furthermore, you can connect a large hard drive to USB and play back saved files directly. In addition to FLAC and WAV, it also supports playback of DSD files up to 5.6 MHz. Scratches on the top plate are quite noticeable. Serial PIIV001248JP (Fujisawa Yukishi)
Maintenance information: 2026.5.13 operation confirmed
Accessories: remote control, power cord
Main specifications: Compatible media iPod/iPhone 1 system (digital direct) USB memory, 1 external USB hard disk system (DSD, FLAC, WAV, MP3, WMA, AIFF, ALAC) optical digital output 1 system, coaxial digital output, RCA1 system, frequency characteristics 4 Hz to 90 kHz (-3 dB), dimensions W435 x H99 x D331mm, weight 7.5 kg
RCA cable, 1.0 m pair, 6N-7N hybrid conductor, twin core structure, thick and strong mid-range, it is a hidden name cable recommended for vintage audio (Tomoho Asaine)
Maintenance information: 2026.5.13 continuity confirmed
Accessories: none
RCA cable, 1.0 m pair, 6N-7N hybrid conductor, twin core structure, thick and strong mid-range, it is a hidden name cable recommended for vintage audio (Tomoho Asaine)
Maintenance information: 2026.5.13 continuity confirmed
Accessories: none
A standard cable with natural, unobtrusional sound quality using a 1.0m pair of 6N+5NCU hybrid 4-core shielded collet chuck pin plugs. It is suitable for classical music and vocals. The exterior has a feeling of use such as dullness (Tomoho Asaine)
Maintenance information: 2026.5.13 continuity confirmed
Accessories: none
It is an RCA cable that is easy to handle with a 0.5 m pair, has a straightforward tone, and a sturdy structure. The exterior is dull (Tamura Eiji)
Maintenance information: 2026.5.13 continuity confirmed
Accessories: none
It is an RCA cable that is easy to handle with a 0.5 m pair, has a straightforward tone, and a sturdy structure. The exterior is dull (Tamura Eiji)
Maintenance information: 2026.5.13 continuity confirmed
Accessories: none
It is an RCA cable that is easy to handle with a 0.5 m pair, has a straightforward tone, and a sturdy structure. The exterior is dull (Tamura Eiji)
Maintenance information: 2026.5.13 continuity confirmed
Accessories: none
Each switch, lamp, volume replacement, etc. have been maintained! Preamps were sold during the heyday of analog. Compared to C29 and later amplifiers, it has a rich and glossy mid-range. This is truly a preamp representing the golden age of McKinn. There is rust and dullness. There is peeling on the center button. Serial AS3194 (Murakoshi Yoichi)
Maintenance information: 2026.4.13 maintained (each SW/VOL cleaning, lamp deterioration replacement, pin jack earth float → plating line treatment, shield cable terminal solder treatment, push button TAPE 1 and 2 dismantling cleaning, pin jack cleaning, glass panel peeling correction (push button part cannot be fixed), shield cover creation, main VOL replacement)
Accessories: instruction manual
Main specifications: input terminals, RCA4, PHONO input, 2 pre-out systems, W445 x H195 x D395 mm, 16 kg
Maintenance completed in February 2025. A high output power amplifier representative of the Lux Kit. As with the original, the output tube was replaced with a GE 6550A, and the sound that combines both tasteful luster and strength is attractive. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2025.2.21 maintenance completed (all 4 output tubes 6550A replaced, 6AQ8 replaced, 2 RCA jacks replaced for deterioration, simple external and internal cleaning, re-soldering treatment at several parts of the board, vacuum tube socket caulking repair, and other measured output 50W (8Ω) measured with AC100V)
Accessories: none
Main specifications: mulard type drive circuit adopted 50W+50W W465×H168×D206mm 17kg
The price has been reduced! 2026/5/11 sales price 1,200,000 yen Maintained by the manufacturer in 2025! It's a crossbow preamp that follows the Cello ENCORE 1MΩ flow. The sound is innocent yet supple and nostalgic. It is a valuable car where you can experience the awesomeness of the infinitely neutral and transparent sound that VIOLA promotes without any coloring. *Gaps between VOL-30 and -20 remain, but the supply of repair parts has been discontinued, so this is the current situation. Serial 0266 (Fujisawa Yukishi)
Maintenance information: 2025.10.9 manufacturer maintained (attenuator readjusted. (There is still a gap between -30 and -20, but the supply of repair parts has been discontinued, so this is the current situation.) 2025.5.14 Manufacturer maintenance completed (volume contact cleaning, contact misalignment, contact float correction at specific contacts, shaft rotation misalignment VOL. Position correction)
Accessories: instruction manual, power cord, connection cord
Main specifications: fixed resistance switching type analog amplifier circuit module equipped with 4 output systems (XLR x 2, Fischer x 1, RCA x 1), 6 input systems (XLR x 1, Fischer x 1, RCA x 4) TAPE OUT (RCA x 1) main body W445 x H110 x D430 mm 9 kg power supply unit W225 x H110 x D400 mm 7.6 kg
The price has been drastically reduced. 2026/5/9 sales price 448,000 yen Fully maintained, including replacement of deteriorated capacitors, resistors, etc. The 220V specification (with 100V to 220V step-up transformer) is still popular even now, 70 years have passed since its release. The thickness, luster, and tension of the sound are all emotionally composed, and perfectly express the sound of the instrument. Anyway, it is a famous machine with thick, firm mid-bass, and a tasteful sound unique to vacuum tubes. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance Information: 2026.5.9 Maintained (QUAD2: Step Up Transformer Additional Block Capacitor 16 μF x 2 Hum Noise Replacement and Mounting Bracket Manufacture 1 x 2 Oil Capacitor 0.1 μF Deterioration Replacement x 2 Electrolytic Capacitor 22 μF Deterioration Replacement 1 x 2 x 2 Resistance 3W Deterioration Replacement 1 x 2 QUAD22: Vacuum Tube EF86 Replacement (2026.4.13 Supply Arrived) Adapter Missing 2 Block Capacitors Manufactured 16 μF x 3 → 3 additional electrolytic capacitors, 4 electrolytic capacitors, 22 μF deterioration replacement, 4 film capacitors, 0.1 μF, other deterioration exchanges, 2 resistors, 1 W and 1/2 W replacement, 8 gang error improvement measures → 1/4 W additional resistors, 5 AC plugs, additional vacuum tube socket and RCA jack caulking repair ※ Other operation check with AC 220V (rated output 13 W SP: 16 Ω wiring)
Accessories: power cable, copy of instruction manual, step-up transformer
Main specifications: 13W (16Ω) with rated output AC220V QUAD22: EF86 × 2 ECC83 × 2 input PHONO, RADIO, TAPE W267 × H89 × D148 mm 3.2 kg QUAD2: KT66 × 4 EF86 × 2 GZ32 15W+15W W321 × H162 × D119 mm 8.2 kg
The price has been drastically reduced. 2026/5/9 sales price 178,000 yen A pre-main amplifier with a low center of gravity, thick enough to listen to. It is a product where you can feel the culmination of Denon, which has a wide high range and high transparency. While it has plenty of driving power, it is an attractive premain with a glossy mid-high range expression. You can see a feeling of use, such as appearance, dullness, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2026.5.5 operation confirmed
Accessories: instruction manual, power cable
Main specifications: 120W+120W (8Ω) 4 input systems (RCA) PHONO1 system (MM/MC) W434 x H181 x D494 mm 29 kg
The disposal price has been reduced! Member prices are not applicable. 2026/5/2 sales price 698,000 yen Maintained! A mono power amplifier with a fully balanced design worthy of being called the culmination of TRIGON. The two completely independent amplifiers inside control the movement of the speaker unit's diaphragm with independent power amplifiers for an astonishing response.*Since BTL amplifiers also emit a signal on the negative side of the speaker terminal, please do not share the negative side. The exterior has dullness and small scratches. Serial 2129, 2130 (Fujisawa Yukishi)
Maintenance information: 2026.5.2 Maintained (push switch replacement (both units) created due to insulator damage. Fixed because the ribbon cable clamp came off. Loosen the screws and tighten them. Bias and offset checks. I checked the output sound. *This model has a BTL configuration. There is also an audio output on the negative side of the speaker terminal. (Please do not ground or share the negative terminal)
Accessories: power cord
Main specifications: maximum output 650 W (4 Ω), 400 W (8 Ω) input RCA x 1, XLR x 1 output XLR (line output for bi-amp) input impedance 47 kΩ playback frequency band 0.5 Hz to 250 kHz W299 x H170 x D464 mm weight 23.9 kg
It was overhauled in 2024/9, including the creation of a new dust cover and the replacement of 16 deteriorated parts. This is a TD-520SUPER+3012R system with gunmetal turntable specifications. The sound quality is delicate, soft, and warm due to the stability of the gunmetal turntable and the smoothness of the belt drive system. A suspended floating suspension has been introduced, and the regeneration system and rotation system are completely independent from motor vibrations. The exterior is dull, and there are some bumps and small scratches. Serial 12797 (Yamato Yuki)
Maintenance information: 2024.10.26 Maintained (electrolytic capacitors, semi-fixed VOL for rotation speed adjustment, semi-fixed VOL replacement for sensor sensitivity adjustment and board re-soldering. Front panel pitch adjustment VOL fixation correction and internal cleaning. Arm disassembly/cleaning, arm shaft bearing replacement. Disassemble and clean the clutch part, and replace the felt. RCA connector replacement. Grease up the platter bearing. Lubricate the motor shaft and adjust the floating. Check the turntable rotation speed and check the arm needle pressure. Check the sound output. Chassis cleaning. Comprehensive operation confirmation inspection dust cover newly created)
Accessories: English instruction manual copy shell (SME S-2) transport lock pin x 2
Main specifications: TD-520-SUPER/ drive system belt drive motor 16 pole synchronous motor speed 33 1/3, 45, 78 rpm, electronic speed selection dimensions W550 x H180 x D410 mm weight 15 kg (main body only) SME: 3012 r/type static balance universal type effective length 307.3 mm compatible cartridge weight 9.5 g to 34 g
Maintained. A LINN core player directly related to the CD12 where you can enjoy a unique sound with a vintage sound vibe. It is still popular today, and the pleasant, smooth sound makes you relax and enjoy the music. The exterior has been cleaned, but marks like spots remain due to paint melting, and there is a feeling of use such as dullness. Serial 003064 (Tomonori Asaine)
Maintenance information: 2026.5.12 maintained (organic solvent cleaning after disassembling the servo mechanism, hardened grease cleaning tray, and height adjustment due to deterioration of each drive belt of the clamp mechanism part, due to misalignment of the upper and lower heights of the replacement tray due to deterioration of the upper and lower heights of the replacement tray, aging test on a commercially available CD disc)
Accessories: remote control power cable
Main specifications: 3 HDCD compatible analog output systems (RCA x 2, XLR x 1), 3 digital output systems (BNC x 1, TOS x 1, AES/EBU x 1) W320 x H80 x D326 mm 4.1 kg
RCA cable, 2.0m pair, L-shaped plug on one side, is a well-known Neumann RCA cable from the prestigious German family. Recommended for those who listen to classical music on records. Since it is slender and soft, it is useful in a variety of situations. You can see the exterior, dullness, and feeling of use (Murakoshi Yoichi)
Maintenance information: 2026.5.12 continuity confirmed
Accessories: none
The price has been reduced! 2026/5/9 sales price 578,000 yen This is a 32-bit dual mono D/A converter that can also play PC audio via SACD or USB connection. Inheriting the design of the previous model D-02/K series, audio performance was further refined by adopting a 32-bit D/A dual mono configuration and a parallel configuration for buffer amplifiers with RCA analog output. It is a high-performance machine unique to modern SOLID and high SN models. The exterior is good with little feeling of use. Serial G30600230B (Takahashi Nobuyuki)
Maintenance information: 2026.5.8 operation confirmed
Accessories: instruction manual, power cable, remote control, original box
Main specifications: W440 × H132 × D410 mm 17.0 kg
The price has been drastically reduced. 2026/5/7 sales price 178,000 yen Maintenance such as LEVEL volume replacement and main VR disassembly and cleaning was completed in 2021/12. The second-generation premain amplifier for NEC's masterpiece A-10. Occasionally, it makes a surprising sound when it touches the strings. It drives jazz and rock briskly with thick low frequencies and clear mid-high frequencies. Another reason for its popularity is that it is easy to separate power from pre. There is a feeling of use on the exterior, such as stains and dullness on the left side of the front panel, scratches on the VOL, paint peeling, etc. Serial 04Y0959 (Takasaki Atsushi)
Maintenance information: 2021.12.25 maintenance completed (POWER AMP LEVEL volume x 2 replacement, main VR disassembly, cleaning, input/output waveform confirmation, left and right balance confirmation, load test, comprehensive operation test to confirm normal operation, input/output waveform confirmation, rated output test (1kHz sine wave, at 8Ω load: 60W+60W, OK), sound output test) 2020.9.21 maintained (power lamp converted to LED, (Transistors, capacitors, fuses, heat dissipation sheets, IC relays, resistors, semi-fixed resistors, diodes, and power supplies SW/SP terminal replacement, re-soldering after removing old solder from substrates, switch relay/VR contact cleaning, RCA terminal cleaning/plating processing, circuit adjustment, exterior cleaning, confirmation of each input/output, running test)
Accessories: copy of instruction manual
Main specifications: output 60+60W (8Ω) phono MM/MC W430 × H150 × D430 mm 23.2 kg
Maintained! Stax headphones+driver set Although it is entry grade, you can enjoy the expansive sound field expression and fresh sound typical of Stax. There is a slight flaw in the head pad (Oikawa Tetsuji)
Maintenance information: 2026.5.11 Maintained (replaced due to power circuit resistance disconnection. I checked the volume and input circuit. I checked the headphone sound. Each input was checked and the terminals were cleaned)
Accessories: power cable
Main specifications: SRM-006ts: frequency characteristics DC to 80 kHz (when using SR-407 x 1 unit) harmonic distortion ratio 0.01% or less/1 kHz (when using SR-407 x 1 unit), rated input level 100 mV maximum output voltage 300 V input impedance/50 kΩ (RCA), 100 kΩ (XLR) input terminal/XLR x 1, RCA x 2 (parallel out terminal) bias voltage DC580V power supply voltage AC100V 50/60 Hz power consumption 49 W vacuum tube/6FQ7 x 1, 6CG7 x 1 W195 x H103 x D380 mm (including protrusions) weight 3.4 kg SR-407: electrostatic ear speaker, open rear type, high moisture permeability, high-grade artificial leather earpads, playback frequency 7 to 41,000 Hz, cable length 2.5 m, 340 g (main body only)
An affordable Lax interconnect cable with attention to detail, such as each core structure that combines the hot and cold of the 1.0m RCA cable transmission line and a core wire wrapped in Japanese paper. It is characterized by its moderate thickness and good S/N. (FUJISAWA KOSHI)
Maintenance information: 2026.5.11 continuity confirmed
Accessories: No accessories
RCA cable 1.5m pair REAN (Neutrik) plug*The color is different on the left and right. Modern version of the 8412 with all-Teflon insulators. This cable is more instantaneous than its price. There are characters that have disappeared. (FUJISAWA KOSHI)
Maintenance information: 2026.5.11 continuity confirmed
Accessories: No accessories
Modern version of the 8412 using an RCA cable 1.0m pair REAN (Neutrik) plug all Teflon insulators. This cable is more instantaneous than its price. There are characters that have disappeared. (FUJISAWA KOSHI)
Maintenance information: 2026.5.11 continuity confirmed
Accessories: No accessories
RCA cable 0.9 m pair plug manufacturer unknown Modern version of the 8412 using all-Teflon insulators. This cable is more instantaneous than its price. There are characters that have disappeared. (FUJISAWA KOSHI)
Maintenance information: 2026.5.11 continuity confirmed
Accessories: No accessories
RCA cable 1.5m pair REAN (Neutrik) plug is a standard cable that is natural, has no habit, and can be used for a wide range of purposes. (FUJISAWA KOSHI)
Maintenance information: 2026.5.11 continuity confirmed
Accessories: No accessories
RCA cable 1.5m pair REAN (Neutrik) plug is a standard cable that is natural, has no habit, and can be used for a wide range of purposes. (FUJISAWA KOSHI)
Maintenance information: 2026.5.11 continuity confirmed
Accessories: No accessories
The price has been reduced! 2026/4/27 sales price 19,800 yen RCA cable 1.0 m pair handmade cable. Details such as specifications are unknown, but it is a cable with a wide range that is well-balanced from high to low frequencies. *Please connect the green side of the plug to the amplifier. (FUJISAWA KOSHI)
Maintenance information: 2026.4.27 continuity confirmed
Accessories: No accessories
RCA cable 1.5m was originally designed for car stereos, but of course it can be used for home audio. The plug is flat with a correct chuck specification and the sound quality spreads softly (Murakoshi Yoichi)
Maintenance information: 2026.5.8 continuity confirmed
Accessories: none
The disposal price has been reduced! Member prices are not applicable. 2026/5/2 sales price 128,000 yen with remote control and SD card! Master recorder AD/DA converter for business use. This device was originally developed for master recording in studios. In addition to PCM192 kHz recording, it also supports DSD 2.8/5.6 MHz recording and playback. It can also be used as an AD/DA converter. It is also compatible with file name editing etc. using only the main unit or connecting to a USB keyboard. It also has plenty of input/output terminals, and is also multi-functional as an AD/DA converter. This is an excellent device that allows you to record and edit high-resolution sound sources with just one unit. *Depending on the standard, SD cards may not be played, but these are specifications. As for the exterior, there is a slight unevenness in the display. (TAMURA Eiji)
Maintenance information: 2026.5.2 operation confirmed
Accessories: remote control, SD card, power cord
Main specifications: Compatible media/SDHC card (4GB to 32GB) /CF card (1GB to 64GB) Type I/*Only files can be copied with CF/SD to USB memory (2GB to 64GB), recording and playback format/44.1/48/88.2/96/176.4/192 kHz (16 bits/24 bits), analog input/output/RCA/balanced XLR digital input/output/S/PDIF/CASCADE, input Frequency/SRC off 44.1/48/88.2/96/176.4/192 kHz, SRC on 32 to 216 kHz W483 × H45 × D305 mm 4.2 kg