Comes with a self-made stand and insulator! The unit is FOSTEX's FE108E-Sigma full range 1, and the subtlety of the sound and spread of the sound field are pretty well tuned in this box. Please give it a try. You can see a feeling of use such as appearance, dullness, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2025.6.8 operation confirmed
Accessories: self-made stand
Main specifications: 10 cm full range (1 way) impedance 8 ohms frequency characteristics 40 Hz to 45 kHz (+/ -5 dB) efficiency 92 dB maximum input 30 W (continuous) 60 W (peak) W187 x H835 x D390 mm approx. 16 kg (measured) foot width 330 mm
A speaker system equipped with a Beima full-range unit in a self-made enclosure. It has a sense of speed, is delicate, and goes well with stringed instruments, so I recommend it. There are scratches and uneven paint on the exterior (Tamura Eiji)
Maintenance information: 2025.6.5 sweep check OK
Accessories: none
Main specifications: 30cm full range impedance 8Ω playback frequency band 100Hz to 18kHz output sound pressure level 102 dB W450 x H700 x D350 mm weight 17.5 kg
*Currently sold. Self-made 2-way speaker equipped with Infiniti's EMIT. Details are unknown, but it seems to be a unit configuration similar to Teshimal. The sound is mellow and relaxing. There is no saran net, and the cabinet is scratched, faded, etc. (Oikawa Tetsuji)
Maintenance information: 2025.5.22 operation confirmed
Accessories: none
Main specifications: W257 x H440 x D190 mm 5.9 kg
Maintained! Equipped with the rare RMA309 early model! It is a 301 system assembled with a compact self-made board type cabinet. You can enjoy a dense and gutsy sound in a compact size. A 7-pin plug is attached to the arm wiring and a phono cable is connected. Serial 77535 (Murakoshi Yoichi)
Maintenance information: 2025.5.28 Maintained (301: AC cord deterioration → replacement. Motor disassembly, inspection, lubrication and assembly. Motor suspension spring rubber deterioration → replacement. The idler spring is out of order → replace it with a new one, adjust it. Main bearing disassembly, oil filling, oil sealant application, assembly. Remove the neon lamp. Suppressor deterioration → rebuild replacement. Idler hardening → replacement with a new one. Oil felt replaced with a new one. Mount bolts, nuts, and rubber washers are attached as new. running test. RMA309: Output connector part modified and removed, restored to original specifications. Internal wiring replacement, horizontal bearing damage correction and adjustment. Counterweight rubber joint deterioration, replacement, and adjustment. Install output terminals and manufacture output cables. Main weight position adjusted at 32g (SPU-A dead weight). Operation, continuity check)
Accessories: instruction manual (copy), phono cable, mounting screws
Main specifications: 301: idler drive/33, 45, 78 rotation compatible RMA309: tone arm for A shell dynamic balance type needle pressure 0 to 7 g W470 x H183 x D470 mm
The price has been drastically reduced. 2025/5/13 sales price 99,800 yen Maintained! A rare boost transformer with TYPE 0.32M-15.241 cased in a self-made chassis. It goes well with the SPU, and you can listen to wonderful vintage sounds with sticky mid to low frequencies and sharp high frequencies. Please note that the gain is quite high (Murakoshi Yoichi)
Maintenance information: 2023.8.18 Maintained (RCA jack detachable, wiring corrected, running test)
Accessories: none
Main specifications: boost ratio 163 times primary impedance 1.5 Ω secondary impedance 40 kΩ size W123 x H82 x D 80 mm weight 244 g (actual measurement)
The disposal price has been reduced. Member discounts are not applicable. 2025/1/14 sales price 25,000 yen. ※ Because it is in poor condition, it is cheap and is sold as is. It is a combination of Fostex's popular unit FE206EN and a self-made enclosure. In addition to the exterior and back frame falling off, corn paper, and there are stains and mold on the edges, there is a lot of feeling of use such as repair marks, packing tape marks, side cracks, dullness, scuffs, etc. (Kobayashi Hitoshi)
Maintenance information: 2025.1.11 Operation confirmed
Accessories: none
Main specifications: 20cm full range playback frequency band: FO to 20kHz output sound pressure level: 96dB/W (1m) input: 90W W290 x H810 x D455 mm 25 kg (actual measurement)
The disposal price has been reduced! Member prices are not applicable. 2022/7/16 sales price 100,000 yen wooden 46cm double woofer type. Baffle opening diameter 425mm, screw pitch 490mm, baffle and enclosure plate thickness 24mm, duct opening diameter 108mm. Both the front and back panels cannot be removed. There are color differences on the left and right sides of the exterior, and there are chipped corners, dents, and stains. (TAKIMOTO Yutaka)
Accessories: none
Main specifications: W1600 x H950 x D850 mm (actual measurement) The weight has not been measured, but it seems that it is 100 kg or more.
The disposal price has been reduced. Member prices are not applicable. 2024/11/26 sales price 29,800 yen corner type bass reflex type enclosure. *Since 8 screws are arranged, units with 4 holes cannot be mounted. There are scratches and chipped corners on the exterior, peeling of the decorative plate, and stains on the saran net. (TERAMOTO Yoshihiko)
Main specifications: W840 x H1145 x D585 mm 41.3 kg (1)/(measured) screw pitch 370 mm
ASW enclosure with a height of 2380 mm. Finished with plywood and wood grain veneer, it looks beautiful. The bass reflex hole has 2 slits and no ducts. It is for 38 cm units, and since the upper cabinet has a large volume, you can expect a low range with plenty of room. Unit mounting hole diameter: 350 mm, screw pitch, 370 mm diagonal, plate thickness 27 mm There are stains, scratches, and stains on the exterior. (TAKIMOTO Yutaka)
Accessories: 14 unit screws (2 missing) *The trolley is not included
Main specifications: upper part: W488 × H1520 × D475 mm 46.8 kg (actual measurement) lower part: W488 × H860 × D475 mm 31.2 kg (actual measurement) total weight 78 kg/unit
Disposal price reduction. 2012/4/2 sales price 10,000 yen Self-made arm board for TD-124 There is an arm hole for the SME3012R The hole is angled in consideration of the escape path of the arm cable W150 x H12 x D400 mm (actual measurement) (Kojima Yosuke)
Accessories: no accessories
This is a backload horn enclosure with split top and bottom. The exterior has scratches, dirt, and holes, and the baffle screw part is buried on one side. (TERAMOTO Yoshihiko)
Accessories: none
Main specifications: W500 x H870 x D280 mm 15.1 kg (1 bottle)/(actual measurement) opening diameter 95 mm
Set of 3 A self-made insulator that imitates “drinking,” which is sometimes used as an insulator. The warm atmosphere is attractive (Daiki Goto)
Accessories: none
Main specifications: Weight approx. 100g
A large self-made audio board with a sturdy wooden board sandwiched between a floor mat and felt. It was created by the previous owner for TANNOY Westminster. As for the exterior, there is a feeling of use such as scratches on the bottom (Tamai Jun)
Accessories: none
Main specifications: size W1040 x D700 x H23 mm weight 8.0 kg
※Inexpensive because it is in poor condition. Self-made 2way/3way enclosure. The size of the hole is different at the top, with an opening diameter of about 315 mm on the top and about 360 mm on the bottom. There are many peeling veneer, corner pads, scratches, etc. (Oikawa Tetsuji)
Accessories: none
Main specifications: W450 x H1056 x D480 mm approx. 33 kg
Self-made enclosure. The previous owner attached a JBL 38cm unit with a 1" driver and used it in 2 ways. It comes with casters. There is a lot of feeling of use, such as uneven paint. Please contact us for shipping (Murakoshi Yoichi)
Accessories: none
Main specifications: W500×H790×D604mm 53.4 kg
A 38cm double configuration enclosure that can be used as a center woofer or center speaker. The previous owner had an electro voice 38cm woofer installed. Comes with casters. There is a lot of feeling of use, such as uneven paint and bolt marks on the top plate. Please contact us for shipping (Murakoshi Yoichi)
Accessories: none
Main specifications: W1045 x H790 x D604 mm 52.2 kg
A self-made large record player cabinet where Victor's TT-101 was mounted. SAEC's WE-308SX was mounted on the arm. Shipping costs will be estimated separately (Sasaki Shota)
Accessories: none
Main specifications: W630 x H205 x D570 mm, arm hole diameter 43/29 mm, weight 26.2 kg
Self-made cabinet for GARRARD 301 with double arm specifications. The 3012 Series 2 and SMG-212 were mounted on the tone arm installation port. You can see the appearance, peeling veneer, abrasions, bruises, etc., and a feeling of use (Kobayashi Hitoshi)
Accessories: none
Main specifications: W760 x H265 x D520 mm 14.4 kg (actual measurement)
Self-made enclosure. The woofer opening is about 340 mm in diameter, the horn opening above it is 450 mm x 266 mm, the upper opening is 260 mm x 134 mm, and the tweeter part is about 60 mm in diameter. Shipping costs will be estimated separately (Oikawa Tetsuji)
Accessories: none
Main specifications: plate thickness 25 mm W800 x H960 x D580 mm 54.1 kg (actual measurement)
The price has been reduced. 2020/4/17 Selling price 5,000 yen Unspecified wooden front baffle. If you are a self-made group, come on. There are scratches and stains scattered, uneven painting, corner chips, etc. (Takasaki Atsushi)
Accessories: none
Main specifications: opening diameter 280 mm bass reflex opening W292 × H80 mm W400 × H610 × D20 mm 1.8 kg/sheet
A self-made record cleaner that imitates PAROSTATIK. The core inside is a vinyl sheet wrapped around it. Thanks to the soft core, it is exquisitely comfortable to use. The exterior has a frayed feeling of use (Katsuji Hiura)
Accessories: none
Main specifications: W105mm diameter 30mm weight 9g
Unspecified 3-way enclosure It is a super bargain price with a considerable feeling of use. For experimentation or research, if you are a self-author with confidence in your arm, how about challenging it? (Yoichi Murakoshi)
Main Specifications: W648 x H967 × D457mm 36.8 Kg (Measurement) Woofer opening diameter 300 mm Scoker opening diameter 173mm tweeter opening diameter 102mm