Maintained by the manufacturer with Sun Audio! This model is equipped with CETRON 300B that even enthusiasts will be satisfied with. All other balls are complete models with no complaints about RCA. Equipped with a Tamura Trance which is currently unavailable. The high gain and straight, carefree sound quality is attractive. The heater has safe DC ignition. I can hardly hear any hum. It is a first-class product where you can directly feel the good sound of the 300B linear thermal triode (Sasaki Shota)
Maintenance information: 2025.5.7 manufacturer maintained (each part inspected, 7 electrolytic capacitors replaced, 2 vacuum tube sockets replaced, 4 1L4P lug terminals replaced, 1 block metallized film capacitor replaced, bottom plate replaced, 2 bridge diodes installed, 1 resistor installed, 1 film capacitor installed, spark killer installed)
Accessories: repair statement, power cable, manual
Main specifications: 300B single 8W+8W vacuum tube used: 300B x 2 (CETRON) 6SL7 x 2 (RCA) 5U4G x 1 (RCA) W360 x H210 x D270 mm 16 kg
Manufacturer maintenance has been completed with attention to details such as switch disassembly and repair, capacitor replacement, etc. A new dust cover has been created, and a rare SHURE M44G cartridge is included. DENON record player DP-57L equipped with auto lift up and stop function. It looks elegant, and the arm can be operated up and down with the touch of a button, making it a recommended unit for those who are thinking about starting a record. It is an S-shaped arm only. In addition to stains on the exterior and turntable mat, you can also see a feeling of use such as dullness, scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2025.10.18 Manufacturer maintained (SW disassembly repair, board inspection repair, power capacitor, head amplifier area, capacitor replacement, CDS replacement. Cabinet cleaning, operation sound test)
Accessories: copy of instruction manual
Main specifications: Direct drive 33/45 rotation compatible tone arm part (static balance, electronic control) arm pipe interchangeable type W485 x H185 x D410 mm approx. 11.5 kg
Main volume has been replaced and other switches have been disassembled and polished! The first model in the α607 series. It is characterized by clear, well-penetrating mid-high tones and powerful bass. It excels at sharpness and balance, and you can listen to jazz and rock in particular comfortably. This is one car that shines for its high cost performance. There is a dull feeling of use (Sasaki Shota)
Maintenance information: 2025.12.13 Maintained (main volume replacement. Switch disassembly and polishing (tone, loudness, subsonic, muting, processor, reck-out, MM/MC) output relay replacement. Protector transistor replacement. Solder repairs on the power supply and other main parts. (Interior and exterior inspection and cleaning, pin jack polishing, input/output confirmation, operation inspection)
Accessories: copy of the manual
Main specifications: 105W+105W (6Ω) 90W+90W (8Ω) W448 × H160 × D441 mm 15.7 kg
This is an Accuphase F-20 and F-25 exclusive crossover 5000 Hz chandever board. It is a popular accessory that has become difficult to obtain (Sasaki Shota)
Accessories: No accessories
Key Specifications: Crossover 5000 Hz
Comes with original box! Frequency board for Accuphase F-20 and F-25 channel dividers. It is for 7000 Hz crossovers, which are essential for 3-way configurations (Sasaki Shota)
Accessories: original box, manual
Key Specifications: Chandeber Board for Crossover 7000 Hz
Comes with original box Accuphase chandelier board. Crossover 3500 Hz. Compatible with channel dividers such as F-20 and F-25 (Shota Sasaki)
Accessories: original box
Main specifications: Compatible models F-20/F-25/F-25V crossover 3500 Hz
Accuphase chandelier board. Crossover 12,500 Hz. Compatible with channel dividers such as F-20 and F-25 (Shota Sasaki)
Accessories: original box
Main specifications: Compatible models F-20/F-25/F-25V crossover 12,500 Hz
F-25 line amplifier Output operation for each frequency band divided by crossover frequency is possible. This is an expansion unit required when using 3 ways or more (Sasaki Shota)
Accessories: No accessories
Main specifications: size W48 x H118 x D303 mm approx. 1.0 kg
Accuphase filter amplifier unit. It is a unit for attaching a frequency board and constructing a filter circuit, and is an expansion product for making it 3 ways or more. The exterior is dull (Sasaki Shota)
Accessories: No accessories
Main specifications: W48 x H118 x D303 mm approx. 1 kg
Red console record player cabinet made by Osaka Cable. for DENON motors. It has a double arm design with 2 21mm diameter holes. The dust cover and hinge are missing (Sasaki Shota)
Accessories: none
Main specifications: W530×H72×D533mm 23.5 kg
Maintenance completed in 2024. Equipped with a Philips swing arm. It has a rich, smooth sound that modern players cannot produce, and it is a popular model among analog fans. There is sharpness in the mid to high frequencies, and it reproduces delicate sounds with clear contours. There is a liquid crystal leak at the edge of the display, but it cannot be repaired, and this is the current situation. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.7.2 maintenance (AC sector exchange (3P type))
Internal check, replacement of coupling C, power supply filter C, etc., CD mechanical check, operation check)
Accessories: copy of instruction manual, power cable
Main specifications: Philips TDA1541 chip, 16 bits, 4 times oversampling, 2 analog outputs (fixed/variable), 2 digital outputs, W450 x H109 x D332 mm, 8.5 kg
※1 bottle only. It is a hybrid of aluminum and cast iron with strong rigidity and excellent stability. It is recommended for those who have JBL/4312 class speakers and are worried that the low frequencies aren't tight. There is no spike reception (Sasaki Shota)
Accessories: none
Main specifications: top plate size W300 x D350 mm W350 x H383 x D400 mm (without spikes) 20 kg
※Inexpensive because it is a cleaner only. This wet cleaner is for records only. A wide type that can wipe down the surface of an LP record. The exterior is yellowish. (TAMURA Eiji)
Accessories: none
This is a Nagaoka SP cartridge. If you love SP, please give it a try. (TAMURA Eiji)
Maintenance information: 2025.12.13 sound output confirmed
Accessories: case
This is a popular Yamaha cartridge. The sound quality is characterized by the smoothness of the mid to high frequencies, making it suitable for pop music. There are no bends. (TAMURA Eiji)
Maintenance information: 2025.12.13 sound output confirmed
Accessories: none
Main specifications: Appropriate needle pressure 2.0g dead weight 6g
Digital cable A digital cable aiming for high-dimensional digital transmission with an amplifier built into the 1.0m RCA plug path. I'm addicted to the good extrusion with a flat balance, just like a single wire cable. (FUJISAWA KOSHI)
Maintenance information: 2025.12.13 sound output confirmed
Accessories: instruction manual, original box, AC adapter
An eye-catching headshell with a large Technica logo that came as standard with the company's AT-1500 series tonearms. Designs similar to OrtoFon's M type and FR's FR-S/2 are attractive. (FUJISAWA KOSHI)
Maintenance information: 2025.12.13 continuity confirmed
Accessories: No accessories
Main specifications: plastic molding, measured 13.0 g
KENWOOD silver shell Model unknown. It is a simple design with high versatility. (FUJISAWA KOSHI)
Maintenance information: 2025.12.13 continuity confirmed
Accessories: No accessories
Main specifications: dead weight 11g
Unspecified head shell. It is lightweight and seems to be compatible with light needle pressure cartridges. (FUJISAWA KOSHI)
Maintenance information: 2025.12.13 continuity confirmed
Accessories: No accessories
Main specifications: dead weight 9g (actual measurement)
※There are some cracks on the decorative panel. Maintenance has been completed, such as volume dismantling and cleaning, and disassembling and polishing of each switch! Following the technology at the time of development of the advanced C-2302, a balanced configuration was adopted for the advanced α-X circuit and power supply unit. The sense of strength and driving power of the highest class as a premain is attractive. There are scratches and line marks on the exterior. Serial 622093654 (Fujisawa Yukishi)
Maintenance information: 2025.12.13 Maintained (main volume dismantled and cleaned. Switch disassembly and polishing (input selector, power amplifier direct, source direct, reck-out, turnover, tone, loudness, muting, processor, MM/ MC). Replace output relays and headphone relays. Balance input terminal replacement. Power supply transistor replacement. Main amplifier section volume adjustment, diode replacement. Solder repair. (Interior and exterior inspection cleaning, DC, bias adjustment, operation inspection)
Accessories: No accessories
Main specifications: 160W+160W (8Ω) 190W+190W (6Ω) phono equipped with advanced α-x balance circuit (MM/MC switching) dimensions W460 x H161 x D446 mm weight 33 kg
Maintained! The balance between thickness and sharpness of the sound is good, and it conveys the breath of jazz and rock. The thick sound image and rich mid-range, which cannot be enjoyed with today's amplifiers, are exquisite. The range is moderate but the Old McKinn sound has instantaneous power. The slightly smokier tone than the MC2500 is attractive. Serial 3Y916 (Fujisawa Yukishi)
Maintenance information: 2025.12.13 Maintained (each replaced due to defective and deteriorated input volume, meter lamp, speaker terminal, and RCA jack. Missing screws added, damaged screws and feet replaced. SW type cleaning. Bias and offset checks. Output audio check)
Accessories: copy of instruction manual, power cord
Main specifications: 300W+300W (mono 600W) 0.5 to 16 ohms W483 x H267 x D432 mm 58.1 kg
It is JBL's first control amplifier to be crowned with a graphics controller, and it is a famous machine that still boasts high popularity today. The dry, horsepower sound quality unique to this era is unparalleled in matching with vintage speakers. It is a control amplifier coveted by JAZZ and ROCK fans that has both good extrusion and a clear outline. The exterior includes line scratches and bumps. Also, the JBL logo on the front has been changed. Serial 2581 (Tamura Eiji)
Maintenance information: Maintained on 2015.8.28 (disassemble and clean each SW volume. Capacitor, lamp, and RCA terminal replacement. Resolder and clean each board. (Input/output waveform check, sound output test, aging)
Accessories: No accessories
Main specifications: LINE input 4 systems PHONO (MM) input 2 systems W397 x H170 x D370 mm 8.0 kg
Pioneer DSD compatible network player. Now that production has been discontinued, it is Pioneer's last premium model, which has become even more popular. We have carefully selected high quality parts such as analog and digital independent power twin transformers, and high-performance ESS twin DACs compatible with DSD256. Delicate, three-dimensional sound suitable for the high-resolution era has been obtained (Murakoshi Yoichi)
Maintenance information: 2025.12.11 sound output confirmed
Accessories: remote control, instruction manual, power cord, connection cord, original box
Main specifications: Network PCM192 kHz/DSD256 USB PCM384 kHz/32 bit DSD236 (Windows dedicated driver only) compatible analog output/RCA1 system balance (XLR3) 1 digital input/optical digital input 1 system, 1 coaxial digital input system (gold plated) USB B (rear) 1 system (for USB DAC function) USB A (front/rear) USB memory system (1) DSD, FLAC, WAV, MP3, WMA, AIFF, ALAC) 1 external USB hard disk (DSD, FLAC, WAV, MP3, WMA, AIFF, ALAC) digital output/1 optical digital output, 1 coaxial digital output (RCA) (gold plated) network terminal LAN (100base-TX/10base-T) wireless LAN (IEEE802.11 a/b/g/n compliant) W435 x H121 × D364mm 12.3kg
Comes with a stand. Murata's ceramic super tweeter. The natural resonance frequency is set higher than the playback band using spherical piezoelectric ceramics, and high tracking of the diaphragm with respect to input signals is achieved. Excellent transient characteristics make it possible to reproduce sound that is both delicate and full of realism. Compatible with a wide range of speakers In addition to the exterior and SP terminal corrosion and discoloration, dullness and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2025.12.9 operation confirmed
Accessories: cover, stand
Main specifications: 15kHz to 100kHz 90dB 8Ω diameter 65mm x length 110mm 1.1 kg
Sony 1TB HDD internal audio player. You can enjoy not only high-resolution sound sources such as DSD 5.6 MHz and 192 kHz/24 bits, but also compressed sound sources with high sound quality. If you install the software on your PC or smartphone, you can transfer and operate music data to the HDD. You can see a feeling of use such as appearance, dullness, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2025.12.11 Operation confirmed
Accessories: remote control, power cord
Main specifications: built-in HDD (1TB) playback compatible codec DSDIFF [DSD] /2.8 MHz/5.6 MHz) DSDIFF [DST] DSF/2.8 MHz/5.6 MHz) WAV/maximum 192 Hz/32 bit) AIFF/192 Hz/24 bit) FLAC/192 Hz/24 bit) ALAC/192 Hz/24 bit) ALAC/192 Hz/24 bit) WMA · MP3 · AAC · ATRAC (Non DRM) playback frequency characteristics 2Hz-80kHz audio output (XLR/RCA) EXT terminal (USB type A) W430 x H130 x D390 mm 14.5 kg
Set of 4 Y-lug terminals The generation of noise and distortion is suppressed, and reliable contact and conduction are achieved. There is a light feeling of use and dullness (Kanai Hidetsugu)
Accessories: original box, wrench
Main specifications: 4 pieces (red x 2, white x 2) set, compatible with wires up to 10 square millimeters (about 3.6 mm) of conductor wire diameter, pure copper core/fork inner dimensions: 6 mm
Manufacturer maintained including laser pickup ASSY replacement! Popular SE (special edition) model! High sound quality that surpasses that of dedicated SACD machines in the same class. You can handle everything from pure audio to DVD multi-channel playback with this one unit. WBT's high-grade terminals and internal main wiring use 6N pure copper wire, so you can enjoy clear, high-pitched sound quality typical of esoterics. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2025.12.13 maintenance completed (mechanical parts replacement mechanism including laser pickup ASSY, mechanical parts replacement, ASSY disassembly/cleaning/lubricating, clamper mechanism partial disassembly/rework correction repair carried out, each connector part reworked correction repair carried out, each part inspection/check/operation confirmed, and cleaned)
Accessories: remote control, instruction manual, power cord
Main specifications: Playable discs: DVD video, DVD audio, SACD, CD, CD-R, CD-RW, video CD, DVD-RW video output: DVI terminal 1, S1/S2 terminal 1, video 1, component 1, D1/D2 terminal 1 audio output: RCA1 system, XLR1 system, optical digital x 1 system, coaxial digital x 1 system, i.LINK x 1 system word sync input (BNC x 1) W442 x H153 x D353mm 23.5kg
Maintained! Dinaco tube preamp. An American sound with an outstanding crisp, dry tone and a slight sense of extrusion. There is a lot of feeling of use on the exterior front panel, such as dullness, stains, corrosion, scuffs, etc. (Murakoshi Yoichi)
Maintenance information: 2025.12.10 Maintained (switch contact cleaning, contact grease application. Vacuum tube socket replacement, retighten power switch knob, check input/output operation)
Accessories: none
Main specifications: Rectifier tube 12x4 12AX7 x 4 PHONO1 system line system 3 system tape system 1 system pre-out 1 system W335 x H100 x D220 mm
Tall Boy from Focal's standard class CHORA (Cola) series is in stock for the first time at Hi-Fi. It is a 3-way system using an inverted dome tweeter with an aluminum/magnesium alloy diaphragm and a unique straight fiber cone unit. As expected, the focus is on making sounds that are both reproducible and musicality. There is a scratch on the center cone, and there is a slight feeling of use (Murakoshi Yoichi)
Maintenance information: 2025.12.10 sound output confirmed
Accessories: saran net, spikes
Main specifications: 3-way bass reflex 8 ohm 91 dB W303 x H1053 x D388 mm 21.15 kg
This is a JBL4520 original enclosure that was once active at the Osaka 70 Expo. Double backload floor type. Overwhelming and exciting! It is possible to reproduce deep bass with plenty of volume. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: MA15, self-made casters
Main specifications: Backload horn system/floor type enclosure unit mounting part (hole) diameter approx. 36 cm approx. 41.5 cm between diagonal bolts (actual measurement) dimensions W927 x H1,294 x D767 mm (actual size) reference weight approx. 110 kg